| 856A1000G07 |
No.3 brg locking nut wrench. |
| 856A1001G01 |
Wrench, Keyed - Torque Multiplier |
| 856A1005G01 |
wrench, compressor rotor locking lug. |
| 856A1006G01 |
Wrench, Torque Adapter - Compressor Stator Nuts |
| 856A1130P12 |
Tool Set - Jackscrews (jackscrews) |
| 856A3604P01 |
Wrench - Horizontal Drive Shaft Nut (wrench) |
| 856A1007G04 |
CORE combustin case support. |
| 856A1008G02 |
Fixture, Lift and Turn - CR Aft End and HPTR Fwd End |
| 856A1008G03 |
Fixture, Lift and Turn - CR Aft End and HPTR Fwd End |
| 856A1009G02 |
Adapter, Vertical Lift Fixture |
| 856A3708G01 |
Pusher/puller - Radial Drive Shaft (pusher/puller) |
| 856A3728G01 |
Sealing Plate and Locking Adapter - Core Engine (locking adapter) |
| 856A3728G02 |
Sealing Plate and Locking Adapter - Core Engine (locking adapter) |
| 856A1219G03 |
Heater, HPT Aft Shaft (shaft heater) |
| 856A1369G03 |
Fixture Adapter (adapter) |
| 856A1371G01 |
Cart, Linigage System (cart) |
| 856A1010G01 |
Wrench, Ratchet - C/R Internal Nut |
| 856A1011P20 |
Dial protractor,901034, |
| 856A1011P68 |
Plate, Rigging stg. 1 |
| 856A1011P69 |
Plate, Rigging stg. 3 |
| 856A1012G01 |
Lever, Countertorque - Compressor Stator Vane Actuator Arm |
| 856A3519G03 |
Sling, 3-Leg - AGB Handling (3-leg sling) |
| 856A3525G03 |
Cradle, Removal/Installation - AGB (removal/installation cradle) |
| 856A3588G01 |
Cradle, Removal/Installation - AGB (removal/installation cradle) |
| 856A3598G02 |
Cradle, Remove/Install - Fuel Pump and MEC Package |
| 856A3709G01 |
Fixture, Alignment - AGB |
| 856A1816G01 |
HPC BRACKER SET |
| 856A1015G01 |
Sling - Frames |
| 856A1016G05 |
Stand, Compressor Rotor and HPTR Vertical |
| 856A1018G02 |
Stand, Subassembly Frames |
| 856A1018G03 |
combustion case overhaul support. |
| 856A1019G03 |
Fixture, Vertical Lift - Comb Case Assy, Aft |
| 856A1019G04 |
Fixture, Vertical Lift - Comb Case Assy, Aft |
| 856A1021G02 |
Fixture, Lift and Turn - C/R Assy Fwd End |
| 856A1023G01 |
Driver, Nut Start - Compressor Rotor Stg 3 to 4 Flange Bolts |
| 856A1421G02 |
FIXTURE,LIFT-HP COMPRESSOR STATOR CASE,FRONT ASSEMBLY |
| 856A1005G02 |
WRENCH-COMPRESSOR ROTOR LOCKING LUG |
| 856A1815G06 |
Motor, Drive - Core Engine Rotation (Foot operated) (drive motor) |
| 856A1042G08 |
Torque Wrench |
| 856A1314G02 |
Bracket Set, Support |
| 856A3709G02 |
Alignment Fixture |
| 856A3922G01 |
AGB/TGB removal/installation kit |
| 856A1025G02 |
Locator, Seal Wires - Compressor Rotor |
| 856A1027G01 |
Fixture, Lift - C/R Stg 3 Disk and Blades |
| 856A1028G01 |
Fixture, Lift - C/R Stage 1-2 Spool, Aft, and Stg 4-9 Spool, Fwd |
| 856A1034G01 |
Wrench - 35-Tooth Bevel Gear Locknut |
| 856A1035G01 |
Fixture Holding - No. 3 Brg IGB Retainer Nut |
| 856A1037G01 |
Wrench, Puller Ring - IGB Module |
| 856A1038G01 |
Fixture, Installation - IGB Bearing and Spacer |
| 856A1039G01 |
Adapter - Inlet Gearbox to Power Arm |
| 856A1040G01 |
Fixture, Removal - IGB Bearing and Spacer |
| 856A1044G02 |
Fixture, Chill - Fwd Flange, Stg 4-9 C/R Spool |
| 856A1048G02 |
Table, Anti-torque - Tooling IGB Module |
| 856A1050G04 |
Fixture, Inspection Shimming IGB |
| 856A1051G02 |
Puller, Arm - Compressor Stator Actuation |
| 856A1053P01 |
Fixture, Impingement Check - Lube Jet |
| 856A1054G02 |
Tool Set, Installation and Removal - Retainer Pin, IGB to No. 3 Brg Nut |
| 856A1057 |
Fixture, lift nad turn - HPT Rotor assy, aft |
| 856A1057G04 |
Fixture, Lift and Turn - HPTR Assy Aft |
| 856A1058G01 |
Vibrator-HPC blades removal/installation. |
| 856A1062G03 |
Fixture, Chilling - HPTR Forward Flange Horizontal |
| 856A1068G02 |
Gage, Locking Lug - C/R Assy |
| 856A1071G05 |
Tool Set - Compressor Stator Vane Segments and Liners Removal |
| 856A1071G06 |
Tool Set, Removal - C/S Liners and Vane Segments |
| 856A1072G04 |
Truck, Compressor Rotor Horizontal |
| 856A1073G03 |
Truck, HPT Rotor Horizontal |
| 856A1075G01 |
Fixture, Lift and Turn - HPTR Disk |
| 856A1075G02 |
HPT disk lift/turn aft fixture. |
| 856A1077G02 |
Pin Set, Guide - HPT Seal to HPT Disk |
| 856A1081G03 |
Dolly, Core Module - Horizontal |
| 856A1081G04 |
Dolly, Core Module - Horizontal |
| 856A1081G05 |
Dolly, Core Module - Horizontal |
| 856A1082G01 |
Fixture, Lift - HPT Rotor, Vertical |
| 856A1083G02 |
Fixture - Lift and Turn - Core Module |
| 856A1084G04 |
Cart, Stator Actuator |
| 856A1084P59 |
VSV hydraulic actuator adaptor. |
| 856A1089G01 |
Wrench - HPTR to C/R Nuts |
| 856A1089G03 |
Wrench - HPTR to C/R Nuts |
| 856A1102G03 |
Adapter, Horizontal Lift - Fixture |
| 856A1107G07 |
Fixture, Lift - Core Module |
| 856A1110G05 |
Stand, Installation - Front C/S Sectors and Liners |
| 856A1112G02 |
Stand, Installation - Rear C/S Sectors and Liners |
| 856A1115G07 |
Cart, Nitrogen - Fuel Manifold Press Check |
| 856A1115G08 |
Cart, Nitrogen - Fuel Manifold Press Check |
| 856A1117G02 |
Fixture, Lift - HPTR Horizontal |
| 856A1125G01 |
Fixture, Lift - Variable CG Rotor to Frames, Horizontal CG |
| 856A1127G01 |
HPT shroud hanger shroud support studs protector. |
| 856A1130G07 |
Tool Set - Jackscrews |
| 856A1130G09 |
Tool Set - Jackscrews |
| 856A1130G10 |
Tool Set - Jackscrews |
| 856A1132G01 |
HPT blades restrain fixture. |
| 856A1140G06 |
Fixture, Support - Core Module to C/R Shaft |
| 856A1603G04 |
Fixture |
| 856A1612G01 |
WRENCH SET SPANNER |
| 856A1351P01 |
Guide Tube Borescope |
| 856A1143G02 |
Fixture, Installation - LP Nozzle Retaining Ring |
| 856A1146P02 |
Fixture, Installation - Inner Cooling Air Duct |
| 856A1150G04 |
Fixture, Buildup |
| 856A1154P02 |
Master, Setup - C/R Buildup |
| 856A1156G01 |
Pylon, Indicator - compressor rotor buildup |
| 856A1157G02 |
Fixture, Lift - Variable CG General Purpose, Heavy |
| 856A1159G08 |
Tool Set, Runout - 110V AC |
| 856A1159G09 |
Tool Set, Runout - 220V AC |
| 856A1159G10 |
Tool Set, Runout - 110V AC |
| 856A1159G11 |
Tool Set, Runout - 220V AC |
| 856A1177G02 |
Truck - HPC/HPT Rotor and Balance Arbors |
| 856A1195G02 |
Fixture, Assembly - HPCR Stg 1-2 Fwd Shaft |
| 856A1196G02 |
Fixture, Lift and Turn - Comb Case Fwd |
| 856A1198G01 |
Puller, Aft Shaft - HPT Rotor |
| 856A1199P01 |
Retainer, Bolt - HPC to CDP Seal to HPT |
| 856A1204G01 |
Fixture, Removal - HPCR |
| 856A1206G05 |
CDP seal runout gage. |
| 856A1206P13 |
CDP seal runout gage. |
| 856A1206P18 |
CDP seal runout gage. |
| 856A3920G01 |
Handling Pump support assy tooling |
| 856A3524P02 |
Tool Set, Drive Adapter |
| 856A3723G02 |
Booster Fixture |
| 856A3793G01 |
FIXTURE PUSH PULL A |
| 856A2644G03 |
HOLDING TOOL |
| 856A1802G04 |
|
| 856A1211G01 |
Fixture, Clamping - No. 3 Bearing Assembly, Inlet Gearbox |
| 856A1213G01 |
Pin Set, Alignment - HPT Rotor Disk to Shaft |
| 856A1216G02 |
4# brg outerace,oil seal puller. |
| 856A1219G02 |
Heater, HPT Aft Shaft, 110V/60Hz |
| 856A1225G01 |
Base, Support - HPT Rotor Buildup/Runout Fixture |
| 856A1252G02 |
HPC rotor bolts installation tool. |
| 856A1257G09 |
Container, Shipping - Core |
| 856A1260P01 |
Gage Set - Inner Stage Seals |
| 856A1265G05 |
Heater - Bevel Gear, Inlet Gearbox, 110V, 60H |
| 856A1266G03 |
Pins, Alignment - Compressor Cases |
| 856A1275G04 |
Compressor Rotor Blades Tip Chord Length Gage |
| 856A1300G02 |
Gage, Length - Core Engine Module |
| 856A1312G01 |
Support, Engine Handling |
| 856A1312G02 |
Handling Supports - Engine Maintenance |
| 856A1312G05 |
Support - Engine Handling |
| 856A1312G08 |
Support - Engine Handling |
| 856A1312P16 |
Support - Engine Handling |
| 856A1312P29 |
Support - Engine Handling |
| 856A1334G03 |
Fixture, Buildup - Core Engine/HP Compressor Rotor |
| 856A1342G01 |
Fixture, Preseat - VSV Lever Arms |
| 856A1344G02 |
Fixture, Setup - Core Engine/HP Compressor Rotor Buildup |
| 856A1352P03 |
Clips, Sensor - HP Turbine Rotor Linipot Runout |
| 856A1356G02 |
Fixture, Lift - HPCR Stage 1-2 Spool, Forward |
| 856A3545G03 |
Fixture Rig AGB |
| 856A3913G03 |
ASSY CHECKING FIXTURE |
| F80113-105 |
Flaring |
| 856A1869G01 |
Push/pull fixture |
| 856A1870G01 |
Push/pull fixture |
| 856A2807G52 |
TEST CELL CONNECTOR |
| 856A1360G01 |
Linipot Runout, 110V AC |
| 856A1360G02 |
Linipot Runout, 220V AC |
| 856A1361G06 |
LINI PROGRAM |
| 856A1369G01 |
Fixture Adapter, Lini-Gage Data Acquisition System |
| 856A1369G02 |
Fixture Adapter, Lini-Gage Data Acquisition System |
| 856A1369P02 |
Linipot gage adapter. |
| 856A1377G01 |
Fixture, Lift and Turn - HPTS/LPTN Assembly |
| 856A1385G02 |
Fixture, Lift - Compressor/LPT, Horizontal |
| 856A1393G01 |
Fixture, Support and Rotation - Core Module |
| 856A1394G01 |
Fixture, Lift - CG Adjustable |
| 856A1452G02 |
HPT rotor support fixture. |
| 856A1519G01 |
Heat - No.3 Lock Nut |
| 856A1818G01 |
Gage, Seating Check - Core Module to IGB |
| 856A1865G01 |
Torquing Adapter-No.3 Bearing Locking Nut |
| 856A2004G02 |
Tool, Assembly - Install/Remove HPTR to Compressor Rotor Nuts |
| 856A2504G01 |
Pusher/Puller, Ferrule - VBV Flexible Shaft |
| 856A2537G01 |
Protector, Mounting Pin - Accessory Drive Major Module |
| 856A2544G02 |
Dolly, Trunnion - Turbine Frame Module |
| 856A2567G01 |
Eye, Lifting - LPT Shaft, Forward |
| 856A2568G01 |
Eye, Lifting - LPT Shaft, Aft |
| 856A2577P01 |
Ring, Locating - No. 5 Bearing Rollers |
| 856A2600G03 |
Tool Set, Guide Shaft and Stop Tools |
| 856A2609G01 |
Block, Jacking - Fuel Pump/MEC or HMU |
| 856A2618G03 |
Fixture, Holding - Rotor/Stator |
| 856A2618G04 |
LPT rotor/stator restraining fixture. |
| 856A2618P08 |
LPT rotor/stator restraining fixture |
| 856A2625G01 |
Stand, Storage - Fan and Booster Module |
| 856A2626G01 |
Stand, Storage - Module 2 |
| 856A2627G05 |
Beam, Lifting |
| 856A2640G01 |
Tool Set Assembly - Ring Oil Separator |
| 856A2645G05 |
Beam, Variable CG - Engine Handling/Lifting |
| 856A2646G01 |
Dolly, Trunnion - Turbine Frame Maintenance Module |
| 856A2647G02 |
LPT horizontal mobile stand. |
| 856A2651G01 |
Pad, Engine Support |
| 856A2651G02 |
Pad, Engine Support |
| 856A2655G02 |
Fixture, Install/Remove - Radial Drive Shaft Housings |
| 856A2661G01 |
Puller - Aft Rotating Air/Oil Separator |
| 856A2663G01 |
splitting fairing puller. |
| 856A2668G01 |
Kit, Puller Adapters |
| 856A2674G01 |
Protection Cover - LPT Shaft |
| 856A2675G01 |
Tool Set,Leak Test-AGB equipment cavity |
| 856A3011P01 |
Plug, Puller - Aft Rotating Air/Oil Seal |
| 856A3012G02 |
Puller - No. 2 Bearing Inner Race |
| 856A3013G03 |
Puller - No. 1 Speed Sensor Ring |
| 856A3033P01 |
No.1 bearing sleeve nut retaining fixture. |
| 856A3062G02 |
Puller, Hydraulic - Rear Rotating Air/Oil Sleeve |
| 856A3074G01 |
Riveter, Balance Weights - Fan Disk |
| 856A3097 |
OIL TUBE CLEAN EQUIPMENT |
| 856A3100G04 |
centering vent tube locating pin. |
| 856A3234P01 |
Protective Cap - Center Vent Tube, Rear Extension Duct |
| 856A3247G03 |
Guide, Alignment - LPT Rear Frame to LPT Shaft |
| 856A3260G02 |
Plug, Extraction - Main Components, LPT Shaft |
| 856A3267G02 |
Adapter, Test Rig - No. 1 and 2 Bearing Support Air Flow Check |
| 856A3268G02 |
Wrench - Sleeve Nut, Center Vent Tube |
| 856A3269G03 |
Wrench - No. 5 Bearing Inner Race |
| 856A3279G02 |
Pusher, Puller - LPT Disk Bushings |
| 856A3308G01 |
No.4 bearing inner race puller. |
| 856A3308G04 |
No.4 bearing inner race puller. |
| 856A3315G01 |
Puller - Center Vent Tube |
| 856A2780G02 |
Adapter, Handling (handling adapter) |
| 856A3485P01 |
Cap, Protective - Thread, LPT Shaft (protective cap) |
| 856A3487G01 |
Protector - No. 4 Ball Bearing (protector) |
| 856A3702G02 |
Sleeve, Centering and Ram/Inst. - LPT Major Module (sleeve) |
| 856A3320P03 |
Ring |
| 856A3322G03 |
Pliers Crimping - No. 5 Bearing Nut |
| 856A3323G01 |
Bushing, Centering - No. 1 Ball Bearing Installation |
| 856A3330G01 |
Tool Set, Seal Fitting - AGB/TGB Oil Nipples |
| 856A3358G03 |
Fixture, Holding - No. 4 Bearing Inner Race Bolts |
| 856A3358G04 |
Fixture, Holding - No. 4 Bearing Inner Race Bolts |
| 856A3703G01 |
Guide, Countertorque Wrench (guide) |
| 856A3704G01 |
Beam, Torque Adaptation (beam) |
| 856A3710G01 |
Beam, Lifting - LPT Major Module (lifting beam) |
| 856A3750G02 |
Fixture, Centering - LPT Shaft (fixture) |
| 856A3773G01 |
Fixture, Handling - LPT Major Module (handling fixture) |
| 856A3794G01 |
Ring, Holding - STG 1 Outer Stationary Seal and Turbine Shroud Support (holding ring) |
| 856A3907P01 |
Ring, Protective Fan Disk (ring) |
| 856A3373G01 |
Fixture, Hoist - LPT Bladed Disks |
| 856A3383G01 |
Fixture, Alignment - LPT Rear Frame to LPT |
| 856A3385P03 |
Wrench - Stage 1 LPT Disk D-Head Bolts |
| 856A3392G01 |
Wrench, Torque - Aft Rotating Air/Oil Separator Nut |
| 856A3413G01 |
holding ring -No.4 bearing rollers |
| 856A3419G02 |
Adapter, Puller - Oil Inlet Cover and Major Module 3 |
| 856A3432G01 |
Gage Tool, Feelers |
| 856A3435G01 |
LPT 1-4th static moment measurement adapter. |
| 856A3443G04 |
Puller, No.5 Bearing - Outer Race and Sleeve |
| 856A3463G01 |
Lever, Countertorque - LPT Shaft |
| 856A3471P01 |
Drive Spline Adpt Fuel Pump |
| 856A3504G03 |
Fixture, Pusher/Puller - Module 1 and Major Module 3 |
| 856A3515G03 |
Extension Beam - Variable CG Lift Fixture |
| 856A3524G01 |
Tool Set, Drive Adapter - Booster and LPT |
| 856A3556G01 |
Tool, Loading - No. 1 Bearing LHA34 Dimension Measurement |
| 856A3570G01 |
Wrench, No. 2 Bearing Inner Race Seal Retainer |
| 856A3571G02 |
Wrench - Forward Rotating Air/Oil Separator Nut |
| 856A3572G01 |
Wrench, No. 1 Bearing Inner Race Nut |
| 856A3576G01 |
sealol and magnetic seals rem/inst. Tool. |
| 856A3591G01 |
Protector, Mounting Pin - Accessory Gearbox |
| 856A3628G01 |
Tool, Installation - No. 1 Bearing Inner Race |
| RSE1098-1 |
after engine mount -spanner wrench |
| RSE1098-5 |
spanner wrench,after engine mount |
| RSE1133 |
Sling |
| RSE1224 |
Retainer, Aft Engine Mount |
| RSE3418 |
HOIST - IDG ACCESSORY |
| 856A1382G06 |
Protector, HPT Shroud LPTN Assembly Stud (protector) |
| 856A1389G01 |
Fixture, Install - No. 4 BRG Outer Race (installation fixture) |
| 856A1433G02 |
Tool, Torque - Manifold Bushing, HP Turbine Stator (torque tool) |
| 856A1453G01 |
Stanchion, Rear Shaft Extension - HP Turbine Rotor (extension stanchion) |
| 856A1454G01 |
Extension, Shaft - HP Turbine Rotor (extension shaft) |
| 856A1490G04 |
Fixture, Install/Remove - Module 12 (install/remove fixture) |
| 856A1491G02 |
Bracket Set, Handling - Compressor Mid Flange (bracket set) |
| 856A1352P04 |
Clip, Sensor - HP Turbine Rotor Runout |
| 856A1159P94 |
Probe - Linipot test |
| 856A2618P15 |
Screw |
| 856A2618P16 |
Nut,.3125-24UNF-2B |
| 856A3906P04 |
Torque wrench |
| 856A1360P04 |
Tube, Guide, HPT linipot |
| 856A1266P11 |
HPC case aligement pin |
| 856A1360P05 |
Linipot Sensor |
| 856A3279P15 |
Pusher,puller,LPT Disks sleeves |
| 856A1508G01 |
Fixture, Heater-HP Turb, Aft Shaft (208-240V, 50-60 Hz) (heater tool) |
| 856A1801G03 |
Ring, Support - Engine Handling |
| 856A1828G03 |
Fixture, Torque No. 4 Bearing Retainer (torque fixture) |
| 856A1836G01 |
Adapters, Maintenance Stand-to-Forward Fan Stator Support Ring |
| 856A2316G01 |
Wrench, Torque/Loosen - LPT Coupling Nut (wrench) |
| 856A2668G02 |
Kit, Puller Adapters (puller adapter kit) |
| 856A3358P03 |
Turning flange |
| 856A1130P08 |
Tool Set - Jackscrews |
| 856A1369P09 |
Rotary Encoder, for linipot computer |
| 856A1000G06 |
TORQUE ADAPTER, I/R - NO. 3 BRG LOCKING NUT |
| 856A2713G07 |
Fixture, Buildup- LPT Shaft to LPT Module |
| 856A1845G01 |
FIXTURE, ALIGNING |
| 856A1334G04 |
Fixture, Buildup - Core Engine/HP Compressor Rotor |
| 856A2600P04 |
Vise-grip plier. |
| 856A1481G02 |
VSV electronic protractor |
| A114301-01 |
Bushing,with puller(Slave race) |
| 856A3501G04 |
FIXTURE, ALIGNMENT / GUIDE BOOSTER / LPT SHAFT |
| 856A1291P02 |
Torque Tube |
| 856A3793G02 |
Fixture, Pusher/Puller - CVT |
| 856A2906P05 |
Clamp |
